Headphones are one of the most common ways to listen to music and other audio. They can get damaged, but with the proper knowledge on how to fix them, you don’t need to go out and spend a lot of money on buying new ones.
After a long day of studying, who wouldn’t just want to relax and listen to some music? The right side has stopped charging, so It often plays static when it works. In this post, I will discuss how to fix broken headphones.
Step 1: Remove Cable from Headphones
There are two ways you can do this step. You can either unscrew the screws on each end of the cable or you can peel off the adhesive that holds in place on both sides. If you’re going to remove adhesive, use a credit card or thin object because there is a thin layer of plastic underneath that needs to be peeled back, making it more tedious.
Once the cable has been removed, you will see two copper coils connected on each side of the red and blue wires that go into the headphones. Pull out the coil on the broken Earbud to resolve the static sound issue.
If it still plays static, there may be gravel or other objects stuck inside, so take a tweezer or small pair of needle-nose pliers to remove. Also, I’m not sure what type of headphones this is but one of my friends told me that if their left ear doesn’t work sometimes, they’ll hear it in their right ear, so maybe try flipping the cable around.
Step 2: Solder new wire to remaining Earbud
If you don’t feel comfortable soldering yourself, I recommend taking it to someone who can help you. If you do feel comfortable, then this should be pretty simple. Just get a thin wire of the same thickness as headphones and solder one end on the remaining earbud coil (the side that doesn’t play static).
Keep in mind it is vital not to leave any exposed wires once you’ve soldered them on because they will short circuit your headphones.
After these steps are done, all that is left is to put some fresh adhesive or screws on each side of the earbuds and place them back into the casing. Put the case back together and enjoy your repaired earbuds.
Must read: How to wear headphones with long hair
How to fix broken headphones on one side?
Don’t be frustrated with the broken headphones on one side. You can fix it.
- First, you need to disassemble the headphones. Make sure you take a picture of the wire connecting the two earpieces before dismantling it.
- This way, you can know how the wire was connected. Now open your voltmeter and feed the tip of the positive lead to the wire connected to the earpiece with the broken wires.
- Get the other end of the wire and touch it with the tip of the negative lead. If a beep is heard, the wires there are dead.
- If no beep is heard, then that means the wire is good. The wires are insulated and cannot be soldered. In that case, you can use the conductive adhesive to secure the wires. Soldering will damage the wires, which will thus have to be replaced.
Conclusion
We hope you enjoyed our article on how to fix broken headphones. If you’re searching for a simple way to fix broken headphones, we highly suggest giving this a try. If this solution works for you, remember to share it with others in the comments section below!
FAQs
How to fix a broken headphone wire?
There are many ways to fix a broken headphone wire, and nothing is better than experimenting on the broken one and finding the best solution. If the wire is only bent out of shape, gently pull it into its original shape while avoiding the wires from touching. If the wires are exposed or broken, then try fixing them to the earbuds with a bit of tape. Although this is temporary, it can save you the cost of throwing your headphones away.
How to fix a broken headphone speaker?
When you hear a crack or pop in your headphone’s speaker, or when the sound output from one side is louder than the other, your headphone’s speaker has likely been damaged. On the other hand, if you hear a crackling noise coming from the headphone’s earphone, then the headphone’s wiring has probably been damaged.
How to fix broken headphones hinge?
If the hinge on your headphones is broken, you can fix them by using a sturdier material. Get your hands on some paracord. Cut a piece of the paracord at least one inch long. Then, take your scissors and snip one of the ends to make a 45-degree angle. Then, you can use the paracord to make a loop.
You might need to cut another end and make a 45-degree angle so that you can slide the loop down the headband. Then, tie the loop to the broken hinge. You can now use the paracord to tie the broken hinge to the band. This technique is pretty easy, and it works well to reinforce the hinge and make sure it doesn’t continue to break.